Search Results for:
LeftField 3 Expert Kit for RED V-RAPTOR (DJI RS 4 & RS 3)
$1,899
Prepare your RED V-RAPTOR for any filmmaking project with a complete accessory package that doesn’t compromise on anything. Directly switch between the baseplate to the DJI RS 4 & 3 without changing plates.
This kit includes the LeftField 3 QR Baseplate (DJI RS 4 & 3, Sliding Top Plate, Top Bar Bracket, Side Plates, Right Side Horse Shoe, Top Handle & Monitor Mount.
- Instant transitions between DJI RS 4 & 3, Tripod or handheld setups
- Built for rigging with secure mounting points with multiple points of safety
- Sliding dovetails allow for faster transition times between setups
- Patented Open•UP quick-release system for snap on, snap off
- Compatible with RED Monitor Interface with mount to relocate monitor
Description
The LeftField 3 System for the RED V-RAPTOR has been built to reliably deliver time after time. The plates provide an extremely rigid frame for rigging with helicoil reinforced mounting points, rosettes for handles & 15mm rod support for EVFs and focus motors.
Time on set is critical, each part of the system has been designed to allow ACs and operators to move faster with quick release dovetails which can be preconfigured during prep.
Multiple safety points have been designed into the system, removing any chance of failure & accidents on set.
What’s Included:
Each Expert Kit (DJI RS 4 & 3) comes with the LeftField 3 15mm LWS Baseplate (DJI RS 4 & 3), Sliding Top Plate, Top Bar Bracket, Top Handle, Side Plates, Right Side Horse Shoe & Monitor Mount.
It is also compatible with the KASBAH shoulder support system with a range of hand grip options and shoulder pad for all-day comfort.
Compatible with DJI RS Gimbals
The DJI gimbal plates ship from the factory with washers of varying thicknesses. While these variations work fine with DJI’s own plate, they may cause clearance issues with the Bright Tangerine DJI compatible plates. This is due to the low-profile design of the protruding support and anti-rotation features, which are crucial for securing the camera.
If you are finding that the bottom of the Bright Tangerine DJI plate is hitting the grey clamp lever and preventing fore and aft slide, you can swap the original washer out with the thinner one supplied in this kit. This will lower the grey lever sufficiently to clear the Bright Tangerine DJI plate. Please note, the use of the thinner washer in this kit will not impact the use of any other baseplates on the DJI camera plate.
Instructions
Replacing The Washer
Step 1: Use a T6 Torx driver (RS4) or 1.5mm hex key (RS 3 and 2) to loosen the central screw and carefully place aside.
Step 2: Carefully remove the clamp lever.
Step 3: Unscrew the clamp bolt. The bolt head resembles a small gear.
Step 4: While unscrewing the clamp bolt, keep the clamp wedge pressed down with your fingers. This will prevent the springs dislodging the clamp wedge.
Step 5: Replace the thicker washer with the thinner one in the kit, and immediately re-screw the clamp bolt back into position.
Calibrating the Clamp Lever
Step 1: Place the Bright Tangerine DJI plate into the clamp as normal. Screw the gear-like bolt head down gently with your fingers until the clamp wedge is just touching the plate.
Step 2: Note how the top of the bolt and the inside of the clamp lever have matching serrated gear-like teeth.
Step 3: Place the clamp lever back over the head of the gear-like bolt head.
Step 4: Before replacing the central screw, swing the clamp lever back and forth and check that the plate is locked in the fully locked position, and is able to slide in the unlocked position.
Step 5: You may need to reposition the clamp lever on the gear-like bolt, by lifting it up and re-engaging it with the teeth in a different position. This is much like using a wrench or spanner on a hex bolt.
Step 6: Once you have got the lever movement tuned and clamping securely, replace the central screw.
LeftField 3 System
Customise your camera build with the extensive selection of accessories in the LeftField system. Letting you create the right setup for each and every task.
This kit has been updated to LeftField 3 and is not compatible with LeftField 2 accessories.
For a complete list of compatible accessories, visit www.brighttangerine.com/leftfield-compatibility
No Compromises
Every part of the LeftField System is machined from single aluminium-alloy billets to create extremely rigid and light weight components. All of which play perfectly to the strengths of the RED V-RAPTOR.
Absolutely no compromise has been made in our manufacturing process. Our engineering is focused on creating products that are both high-performance and enabled with a longer life of service. Combine that with unparalleled level of Bright Tangerine support, and your LeftField V-RAPTOR System becomes the most reliable and hard-working partnership that any filmmaker could wish for.
Additional information
| Weight | 1.187 kg |
|---|---|
| Dimensions | 20 × 20 × 20 cm |
| Camera Brand | RED |
| Camera Model | |
| Gimbal Compatibility | DJI RS 3, DJI RS4 |
