Extended DJI RS 4 & RS 3 Dovetail for RED V-RAPTOR
$129
Mount your RED V-Raptor onto the DJI RS 4 & RS 3 Dovetail for faster transitions between gimbal, handheld & tripod setups.
The dovetail is designed to be paired with LeftField 15mm LWS Baseplates with the DJI RS 4 riser for RED V-RAPTOR.
- Compatible with RED V-RAPTOR
- Slides onto LeftField 15mm LWS Baseplates with DJI RS 4 & 3 riser
- 144mm length provides ample fore/aft range with racking gear
- Shuttle slides fore/aft to balance camera and keep screws captive
- Wide platform for extra stability with rubber pads for grip
In stock
Description
This dovetail mounts onto your RED V-RAPTOR and lets you quickly switch between the LeftField 15mm LWS Baseplate to gimbal or handheld in seconds.
Easily balance your V-RAPTOR on DJI gimbals
The dovetail includes three camera mounting screws (two 3/8-16” & a ¼-20”). Using the three captive screws on the captive shuttle, the camera can be securely mounted with no twisting or movement. The channel allows the camera to be balanced on the plate for weight distribution with the extra width providing added stability while removing any flex.
The dovetail uses the same DJI standard, complete with a racking gear. It works directly with the RS 4 Pro, RS 4, RS 3 Pro, RS 3 & earlier models without the need to change camera plates. The extra length provides ample room for balancing & adjustment.
Laser etched markers along the length of the dovetail let ACs mark down balanced positions on the gimbal.
When paired with our LeftField DJI RS 3 & RS 4 quick release risers, the camera is set at the correct height for 15mm LWS support & accessories.
Support For Accessories
Lens adapters can be secured using the front channel and supplied screws. Depending on the camera height, not all lens feet will be compatible or require spacers.
The broad, flat surface of the universal dovetail ensures your camera remains stable, maximizing surface area to eliminate any flex. Rubber grips prevent twisting, even with smaller cameras.
The camera remains low, creating a natural pivot point for smooth operation with the gimbal.
Compatibility
The DJI gimbal plates ship from the factory with washers of varying thicknesses. While these variations work fine with DJI’s own plate, they may cause clearance issues with the Bright Tangerine DJI compatible plates. This is due to the low-profile design of the protruding support and anti-rotation features, which are crucial for securing the camera.
If you are finding that the bottom of the Bright Tangerine DJI plate is hitting the grey clamp lever and preventing fore and aft slide, you can swap the original washer out with the thinner one supplied in this kit. This will lower the grey lever sufficiently to clear the Bright Tangerine DJI plate. Please note, the use of the thinner washer in this kit will not impact the use of any other baseplates on the DJI camera plate.
Instructions
Replacing The Washer
Step 1: Use a T6 Torx driver (RS4) or 1.5mm hex key (RS 3 and 2) to loosen the central screw and carefully place aside.
Step 2: Carefully remove the clamp lever.
Step 3: Unscrew the clamp bolt. The bolt head resembles a small gear.
Step 4: While unscrewing the clamp bolt, keep the clamp wedge pressed down with your fingers. This will prevent the springs dislodging the clamp wedge.
Step 5: Replace the thicker washer with the thinner one in the kit, and immediately re-screw the clamp bolt back into position.
Calibrating the Clamp Lever
Step 1: Place the Bright Tangerine DJI plate into the clamp as normal. Screw the gear-like bolt head down gently with your fingers until the clamp wedge is just touching the plate.
Step 2: Note how the top of the bolt and the inside of the clamp lever have matching serrated gear-like teeth.
Step 3: Place the clamp lever back over the head of the gear-like bolt head.
Step 4: Before replacing the central screw, swing the clamp lever back and forth and check that the plate is locked in the fully locked position, and is able to slide in the unlocked position.
Step 5: You may need to reposition the clamp lever on the gear-like bolt, by lifting it up and re-engaging it with the teeth in a different position. This is much like using a wrench or spanner on a hex bolt.
Step 6: Once you have got the lever movement tuned and clamping securely, replace the central screw.
Extra Care Comes Standard
Machined and hand-finished in our single factory in Church Crookham from high-grade materials. Hard anodised for extended durability. The Extended DJI RS 4 & RS 3 Dovetail for RED V-RAPTOR comes with our famous Bright Tangerine Support and the addition of a 2-year warranty.
Additional information
Weight | 0.190 kg |
---|---|
Dimensions | 16 × 7.1 × 1.3 cm |
Camera Model | |
Dovetail | DJI RS 4, RS 3, RS 2 |